Socks falling down? Consider elastic

Socks won't stay up? You're not alone. Socks are a very popular item to knit but recurrent discussions on Internet knitting forums show falling-down socks are a problem to many.

There are many, many ways to solve this problem, but one of the most direct is elastic. Here are four different methods.

Elastic garters inside the sock 

TECHknitting blog has already shown how to make knitted hems, both sewn shut and knitted shut.  If you create one of these hems at the top of a sock, you can insert an elastic garter into the hem, thus turning the hem into a "casing" ("casing" = a fancy word for a hem which is encasing something: a hem with something inside of it).
wear the garter around
the house for a while



A few tips:
  • Make the garter out of non-roll elastic because if it gets twisted inside the casing, you'll have a hard time straightening it.  I use 3/4 inch wide non-roll, but some prefer one-inch wide.
  • There are various weights and strengths of non-roll elastics--try to feel of them before you buy because some are quite thick and stiff.
  • Make up the garter by cutting the elastic longer than you think, then pin or tack it down (tack = sew quickly with a couple of big stitches) into a circle of approximately the same diameter as your leg, sock-top-high.  Leave some overlap so you can adjust as needed.  WEAR the pinned/tacked garter around the house for a while, trying it on both legs before you sew it down permanently.  (Elastic garters need not be very tight to do their work--your underwear elastic doesn't bite into your flesh and neither does the elastic on store-bought socks, yet they both work.)  By wearing the garter around for a while, you can adjust it until it is as loose as possible while still doing its job.  Also, remember--it will be slightly tighter inside the casing than around your bare leg, since it has to stretch slightly further. 
  • You can insert the garter into its casing at the sock top either by sewing the casing shut over the elastic as the last step in finishing the sock, or--for a top-down sock--knitting the casing shut as-you-go with the garter trapped inside.  
  • Elastic can loose its oomph long before a handknit sock wears out, so if you do sew the casing shut, use a contrasting color yarn--that'll make it easy to snip and resew a new garter in.
  • An elastic garter sewn into a casing often makes the sock top stand out because the unstretched garter is larger than the unstretched sock top, but when you put the sock on, all will be well. 
...the sock top stands out because the
unstretched garter is wider than the
unstretched sock...

...but when you put it on
all will be well

Thread elastic added afterwards

Another method to make your socks stay up is to use thread elastic, threading this onto a needle and working this around and around the inside of the sock ribbing in a spiral.  The easiest way I know is to catch the elastic under ONE arm of a knit column on the inside.  This is a (receding) purl column on the front of the sock, which helps hide the elastic. Don't over-tension the elastic as you sew it in.  In fact, don't tension it much, if at all--the inside of a sock is a lot smaller than the outside of your leg, so an elastic worked into a sock top must have enough slack to stretch as the sock does.

thread elastic worked into the ribbing at the top of a sock

Working thread elastic into sock ribbing is an good solution for already-made socks.  The only drawback to thread elastic is that it doesn't last very long--a few years at most, whereas a hand-knit sock might last many times that.  However, it is no great chore to snip out the old elastic and insert new.

Knitting in elastic as-you-go

It is also possible to knit in elastic as you go.  This trick is possible with thread elastic, but, unless the thread elastic is the same color as your yarn, there is the possibility of the elastic peeping out when you wear the socks. Plus, you know, thread elastic loses its oomph pretty quick. A better sort of elastic to knit in is a European product called "knitting elastic" which is invisible. (And that's why there's no illustration--it is literally hard to see this stuff even when it's in your hand.)

The trouble with knitting in elastic is knowing how strongly to tension it as you knit. Start by tensioning as little as possible, rather than trying to stretch it as you knit, then tighten up from there if that's unsatisfactory. I haven't used the knitting elastic product very extensively and so don't know how long it is likely to last.  If you have more experience, maybe sing out in the comments? I will say that the stuff has amazing stretch and feels very sturdy, at least when it is new.  It also washes up OK, but I haven't yet tried it in a dryer.

Elastic garters worn outside the sock
The first three methods of adding elastic all work on the inside of the sock.  However, traditionally, it was understood that socks and stockings were likely to fall down, and that's why many ethnic and historical costumes include socks and stockings held up with garters worn OUTSIDE the sock.  (aaand, for history buffs, these garters were traditionally knitted in garter stitch,which is why...)

My maternal grandparents (born 1896 and 1902, respectively) wore ordinary business attire, not ethnic costume, but they did keep their socks up with elastic sock garters every day of their lives--grandpa used the men's version, grandma used an elastic garter at the top of each thigh-high nylon.  Retro-style garters like this are still for sale on-line, and the men's version has always remained part of a formal-wear outfit.

The cheapest modern equivalent to outside garters are rubber bands. Snap one around each sock top, flip the ribbing down, and you're out the door.

For a better-fitting version, you can make custom elastic garters, as in the first part of this post.  However, because these are now meant to be worn outside the sock, under the flip of the ribbing, use narrower elastic.  There is no need to use non-roll elastic either, since you can easily reach the elastic to straighten it. One pair of custom garters will work for all socks of the same length--a time saver over knitting a pair of garters into each pair of socks: easier and less clunky, too.

If you do opt to make elastic garters, you can gussie these up by sewing a ribbon onto the garter, arranged such that the ribbon peeks out from under the folded-down sock top. This trick makes it look as if the ribbon itself is holding up the sock, while the elastic remains hidden. These little ribbon ends are called "garter flashes" and they can also be made out of woolen fabric--particularly for wear with kilt hose.

ribbon-end garter flashes

 (We'll end with a link to a handsome fellow wearing kilt hose held up with garters showing garter flashes. Remember to look at his socks, OK?)

Good knitting, TK
You have been reading TECHknitting blog on what to do if your socks fall down.